Microwave ovens are a typical kitchen equipment that can be utilized to cook dinner, reheat, and defrost meals. They’re comparatively simple to make use of, however eradicating them from the wall is usually a bit more difficult. In case you are planning to maneuver or transform your kitchen, chances are you’ll must take away your overhead microwave. Listed below are just a few tips about how you can do it safely and simply.
Earlier than you start, just remember to have the entire crucial instruments and supplies. You will want a screwdriver, a wrench, and a pair of pliers. You might also want a ladder in case your microwave is mounted excessive on the wall. After you have gathered your instruments, you may start the removing course of. First, unplug the microwave from {the electrical} outlet. Then, take away the mounting screws which are holding the microwave to the wall. As soon as the screws are eliminated, you may rigorously elevate the microwave off of the wall and set it apart.
As soon as the microwave is eliminated, you may disconnect {the electrical} wires which are linked to it. Watch out to not injury the wires, as this might create a hearth hazard. As soon as the wires are disconnected, you may take away the microwave fully. In case you are planning to maneuver the microwave to a brand new location, be sure you pack it rigorously to keep away from injury. You might also wish to think about hiring an expert that can assist you transfer the microwave, particularly if it’s a heavy mannequin.
Disconnecting the Energy Provide
### 1. Shut off the electrical energy to the microwave.
Earlier than you start any work, it’s essential to make sure your security by disconnecting the ability provide to the microwave. Find {the electrical} panel in your dwelling and flip the circuit breaker that corresponds to the microwave circuit to the “OFF” place. You too can unplug the microwave from {the electrical} outlet whether it is linked to 1.
### 2. Anticipate the microwave to chill down.
As soon as the ability provide is disconnected, enable the microwave to chill down for at the least half-hour earlier than trying to take away it. That is to stop any burns from residual warmth within the equipment.
### 3. Take away the mounting screws.
After the microwave has cooled, find the mounting screws that safe it to the wall or cupboard above it. These screws can often be discovered on the highest or backside of the microwave, relying on the mannequin. Use a screwdriver to take away these screws, however don’t take away the microwave from the wall or cupboard but.
### 4. Help the microwave whereas eradicating it.
With the mounting screws eliminated, you’re able to take away the microwave from its place. Get somebody that can assist you elevate and help the microwave when you rigorously slide it out of the wall or cupboard. Be aware to not drop or injury the equipment throughout this course of.
Eradicating the Mounting Screws
As soon as the ability has been disconnected, you may start eradicating the mounting screws. These screws are sometimes positioned on the prime of the microwave, on both facet of the unit. They could be lined by plastic caps or covers, which you’ll be able to gently pry off with a flathead screwdriver.
Utilizing a Phillips head screwdriver, rigorously loosen the mounting screws by turning them counterclockwise. Don’t take away the screws fully at this level, because the microwave remains to be hooked up to the wall by {the electrical} wire and bracket.
As soon as the mounting screws are unfastened, you may gently pull the microwave ahead and away from the wall. Watch out to not pull too exhausting, as chances are you’ll injury {the electrical} wire or bracket.
| Software Required | Steps |
|---|---|
| Flathead screwdriver | Pry off plastic caps or covers |
| Phillips head screwdriver | Loosen mounting screws |
| Gently pull microwave ahead | Detach from wall |
Unplugging the Wiring Harness
Unplugging the wiring harness is an important step in eradicating an overhead microwave. It requires cautious consideration to element to make sure security and stop injury to the equipment. Listed below are the steps concerned:
1. Flip Off Energy and Unplug the Microwave
Earlier than touching any electrical parts, make sure the microwave is disconnected from the ability provide. Find {the electrical} outlet and unplug the microwave from the wall. Don’t yank or pull on the wire, as this will likely injury the wiring.
2. Find and Entry the Junction Field
The junction field is a steel enclosure that comprises {the electrical} connections for the microwave. It’s sometimes positioned inside the cupboard or behind the microwave itself. Entry the junction field by unscrewing the quilt or eradicating any bolts or screws holding it in place.
3. Unplug the Wiring Harness
After you have entry to the junction field, you will notice a bundle of wires linked to the microwave’s wiring harness. Every wire is often recognized by a unique shade. To unplug the wiring harness, observe these steps rigorously:
- Establish Terminals: Find the terminals on the junction field the place the wires from the wiring harness are linked. Terminals are sometimes labeled or color-coded.
- Loosen Screws: Utilizing a screwdriver, loosen the screws on the terminals to launch the wires from the wiring harness.
- Pull Wires: Gently pull every wire straight out of the terminal. Don’t pull on the wire itself, as this will likely injury the wire or the terminal.
- Disconnect Harness: As soon as all of the wires are disconnected, rigorously elevate the wiring harness away from the junction field.
Confer with this desk for a extra detailed visible information to unplugging the wiring harness:
| Step | Description |
|---|---|
| 1 | Establish terminals and loosen screws. |
| 2 | Pull wires straight out of terminals. |
| 3 | Disconnect wiring harness from junction field. |
Eradicating the Trim Plate
The trim plate is the ornamental panel that covers the sides of the microwave oven and conceals its mounting screws. To take away the trim plate, observe these steps:
1. Unplug the microwave oven from {the electrical} outlet.
2. Find the screws that maintain the trim plate in place. They’re sometimes positioned on the highest and backside of the trim plate.
3. Take away the screws utilizing a screwdriver. Watch out to not drop the screws.
4. Gently pull the trim plate away from the microwave oven. It ought to come off simply.
5. If the trim plate is caught, chances are you’ll want to make use of a putty knife or a skinny, flat object to softly pry it unfastened. Insert the putty knife or flat object between the trim plate and the microwave oven and punctiliously pry the trim plate away from the oven. Watch out to not injury the trim plate or the microwave oven.
As soon as the trim plate is eliminated, you should have entry to the mounting screws that maintain the microwave oven in place. Now you can proceed to the following step of the removing course of.
Disassembling the Microwave
PREPARATIONS
Earlier than disassembling the microwave, guarantee energy provide is lower off, plug is faraway from socket, and the system is chilly.
REMOVING THE CABINET
Establish the mounting screws or bolts securing the microwave to the cupboard. Unscrew or unbolt them rigorously. Grip the microwave firmly, elevate it straight up off the cupboard, and set it apart.
DISCONNECTING THE WIRING
Find the wiring harness connecting the microwave to the ability provide and cupboard. Disconnect the harness by unplugging the connectors or unscrewing the terminals. Label wires if crucial for simpler reassembly.
REMOVING THE MOUNTING BRACKETS
Unfasten the mounting brackets attaching the microwave to the wall or ceiling. These could also be secured with screws or bolts; use applicable instruments to take away them.
DETACHING THE DOOR
Open the microwave door absolutely. Find the hinges connecting the door to the microwave physique. Unscrew or unbolt the hinges and punctiliously elevate the door off the microwave.
ACCESSING THE INTERNAL COMPONENTS
As soon as the door is eliminated, you may entry the interior parts of the microwave. These could embody the magnetron, waveguide, fan motor, and turntable motor. Deal with parts gently to keep away from injury.
ELECTRICAL COMPONENTS
MAGNETRON
The magnetron is a vacuum tube that generates microwaves. It’s positioned within the base of the microwave oven and is answerable for heating the meals. The magnetron is a important part and will solely get replaced by a professional technician.
WAVEGUIDE
The waveguide is a steel tube that carries microwaves from the magnetron to the cooking chamber. It is very important hold the waveguide clear and freed from obstructions.
FAN MOTOR
The fan motor circulates air contained in the microwave oven to chill the parts and stop overheating. The fan motor is often positioned at the back of the microwave oven.
TURNTABLE MOTOR
The turntable motor rotates the turntable contained in the microwave oven, making certain that meals is cooked evenly. The turntable motor is often positioned within the backside of the microwave oven.
Cleansing the Microwave
1. Unplug the microwave.
Earlier than you start cleansing, be sure you unplug the microwave from {the electrical} outlet. This may forestall the microwave from by accident turning on while you’re cleansing it.
2. Take away the turntable and turntable ring.
The turntable and turntable ring will be eliminated by merely lifting them out of the microwave. Make sure to wash these things in scorching, soapy water and dry them completely earlier than changing them.
3. Clear the inside of the microwave.
The inside of the microwave will be cleaned with a light detergent and water. Use a sponge or fabric to wipe down the inside surfaces, together with the door, the ceiling, and the edges. Make sure to rinse the inside completely with clear water and dry it with a clear fabric.
4. Clear the outside of the microwave.
The outside of the microwave will be cleaned with a light detergent and water. Use a sponge or fabric to wipe down the outside surfaces, together with the door, the edges, and the highest. Make sure to rinse the outside completely with clear water and dry it with a clear fabric.
5. Clear the door gasket.
The door gasket is a rubber seal that helps to maintain the microwave door closed. Over time, the door gasket can change into soiled and greasy. Use a sponge or fabric to wipe down the door gasket with a light detergent and water. Make sure to rinse the door gasket completely with clear water and dry it with a clear fabric.
6. Clear the vent.
The vent is positioned on the highest or facet of the microwave. It’s used to exhaust air from the microwave. Over time, the vent can change into clogged with mud and particles. Use a vacuum cleaner to wash the vent. Make sure to take away any mud or particles from the vent.
7. Clear the microwave filter.
The microwave filter is positioned behind the vent. It’s used to lure grease and smoke from the microwave. Over time, the microwave filter can change into clogged with grease and smoke. It is very important clear the microwave filter recurrently to make sure that the microwave is working correctly. To scrub the microwave filter, take away it from the microwave and wash it in scorching, soapy water. Make sure to rinse the microwave filter completely with clear water and dry it completely earlier than changing it.
| Cleansing Job | Frequency |
|---|---|
| Clear the inside of the microwave | Month-to-month |
| Clear the outside of the microwave | Month-to-month |
| Clear the door gasket | Month-to-month |
| Clear the vent | Each 3 months |
| Clear the microwave filter | Each 6 months |
Reinstalling the Microwave
1. Flip off the ability to the microwave on the circuit breaker.
2. Take away the mounting screws that maintain the microwave to the cupboard.
3. Rigorously elevate the microwave off the mounting bracket.
4. Take away the ability wire from the outlet.
5. Take away the exhaust duct from the microwave.
6. If the microwave is vented outdoors, take away the vent cap from the outside wall.
7. Clear the mounting floor and the again of the microwave.
8. Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and stop drafts.
| Step | Motion |
|—|—|
| 1 | Flip off the ability to the microwave on the circuit breaker. |
| 2 | Take away the mounting screws that maintain the microwave to the cupboard. |
| 3 | Rigorously elevate the microwave off the mounting bracket. |
| 4 | Take away the ability wire from the outlet. |
| 5 | Take away the exhaust duct from the microwave. |
| 6 | If the microwave is vented outdoors, take away the vent cap from the outside wall. |
| 7 | Clear the mounting floor and the again of the microwave. |
| 8 | Apply a bead of caulk across the perimeter of the mounting floor. This may assist to seal the microwave and stop drafts. |
9. Place the microwave on the mounting bracket and align the screw holes.
10. Insert the mounting screws and tighten them securely.
11. Join the ability wire to the outlet.
12. Set up the exhaust duct to the microwave.
13. If the microwave is vented outdoors, set up the vent cap on the outside wall.
14. Activate the ability to the microwave on the circuit breaker.
15. Check the microwave to verify it’s working correctly.
Reconnecting the Energy Provide
Step 1: Unplug the Microwave.
Earlier than touching any wires, be certain that the microwave is totally disconnected from the ability supply. Find the ability wire and pull the plug from the wall outlet.
Step 2: Establish the Wires.
Inside {the electrical} field, you can see a number of wires linked to the microwave. These wires will sometimes be black, white, and inexperienced (or naked copper) and are held along with wire nuts.
Step 3: Take away the Wire Nuts.
Rigorously take away the wire nuts by twisting them counterclockwise. Be cautious to not injury the wires.
Step 4: Separate the Wires.
As soon as the wire nuts are eliminated, gently separate the black and white wires from one another. The inexperienced (or naked copper) wire is the bottom wire and will stay linked.
Step 5: Join the New Microwave.
Align the wires from the brand new microwave with the corresponding wires from {the electrical} field. Twist the black wire from the brand new microwave with the black wire from the field, and do the identical for the white wires.
Step 6: Safe the Wire Nuts.
Place a brand new wire nut over every set of twisted wires and tighten it clockwise till comfortable. Be certain that the wires are securely linked.
Step 7: Check the Wiring.
Earlier than reconnecting the ability, double-check your connections utilizing a multimeter to make sure correct continuity and no quick circuits.
Step 8: Reconnect the Energy.
Plug the microwave energy wire again into the wall outlet and activate the breaker or fuse to revive energy to the equipment.
Step 9: Check the Microwave.
Press the ability button on the microwave to make sure that it’s functioning appropriately. If the microwave doesn’t activate or operates abnormally, repeat the above steps to verify for any unfastened connections or wiring errors.
Testing the Microwave
Earlier than trying to take away the microwave, it is essential to make sure it is turned off and unplugged from the ability supply. Comply with these steps to confirm the microwave’s standing:
1. Verify the Energy Swap
Find the ability change on the microwave’s entrance or facet panel. Be certain it is turned to the “Off” place.
2. Unplug the Microwave
Find {the electrical} outlet the place the microwave is plugged in. Firmly grasp the plug and pull it straight out of the outlet.
3. Anticipate Capacitor to Discharge
After unplugging the microwave, enable a couple of minutes for the capacitor to discharge. This may forestall any electrical shock hazard.
4. Open the Microwave Door
As soon as the capacitor has discharged, open the microwave door to launch any remaining power.
5. Verify for Residual Warmth
Really feel the within and outdoors of the microwave to make sure it is fully cool. If it is nonetheless heat, wait longer earlier than continuing.
6. Visually Examine the Microwave
Look at the microwave for any injury or unfastened components. For those who discover something uncommon, don’t try and take away it your self and phone a professional equipment restore technician.
7. Collect Essential Instruments
You’ll doubtless want a Phillips head screwdriver and a flathead screwdriver to take away the microwave.
8. Put on Protecting Gear
Placed on security glasses and gloves to guard your self from sharp edges or electrical parts.
9. Disconnect Electrical Wires
As soon as the microwave is faraway from the wall, rigorously disconnect {the electrical} wires from the terminal block. Observe the place of every wire for reconnection later.
10. Take away the Mounting Bracket
Find the mounting bracket that secures the microwave to the wall. Utilizing the suitable screwdriver, take away the screws or bolts that maintain the bracket in place. Watch out to not drop the microwave when eradicating it from the bracket.
How To Take away A Overhead Microwave
Eradicating an overhead microwave is usually a daunting activity, however it’s positively doable to do it your self with the appropriate instruments and a little bit little bit of know-how. Listed below are the steps on how you can do it:
- Flip off the ability to the microwave. This may be achieved by unplugging it from the outlet or by turning off the breaker that controls the ability to the microwave.
- Take away the mounting screws. There are often 4 screws that maintain the microwave in place. These screws are positioned on the highest of the microwave, close to the again. Use a screwdriver to take away the screws.
- Rigorously elevate the microwave off of the wall. As soon as the screws are eliminated, you may rigorously elevate the microwave off of the wall. Make sure to help the burden of the microwave along with your different hand.
- Disconnect the wiring. As soon as the microwave is off of the wall, you’ll want to disconnect the wiring. There are often two wires that join the microwave to the ability supply. Use a pair of pliers to disconnect the wires.
- Take away the microwave from the kitchen. As soon as the wiring is disconnected, you may take away the microwave from the kitchen. Make sure to elevate the microwave rigorously and keep away from bumping it into something.
Individuals Additionally Ask About How To Take away A Overhead Microwave
How do I take away a microwave from a cupboard?
To take away a microwave from a cupboard, you have to to:
- Open the cupboard door.
- Find the screws which are holding the microwave in place.
- Take away the screws.
- Rigorously elevate the microwave out of the cupboard.
How do I take away a microwave from a wall bracket?
To take away a microwave from a wall bracket, you have to to:
- Flip off the ability to the microwave.
- Take away the screws which are holding the microwave to the wall bracket.
- Rigorously elevate the microwave off of the wall bracket.
- Disconnect the wiring from the microwave.
How do I take away a in-built microwave?
To take away a in-built microwave, you have to to:
- Flip off the ability to the microwave.
- Take away the trim across the microwave.
- Take away the screws which are holding the microwave in place.
- Rigorously elevate the microwave out of the cupboard.
- Disconnect the wiring from the microwave.
